2gig Control Panel Firmware Version 1.13 - Quick Progra Bedienungsanleitung PDF herunterladen

GETTING STARTED

To enter the control panel’s System Conﬁguraon module to

program sensor zones and modify sengs:

1. At Home screen, tap logo in lower-right corner.

Enter: Master Installer Code.

Tap: System Conﬁguraon.

2. At Home screen:

Tap: Security > Menu > Toolbox.

Enter: Master Installer Code.

Tap:  Installer Toolbox > System Conﬁguraon

To navigate through quesons and opons in the System Conﬁguraon

module:

Tap or to scroll between opons on the acve screen.

Tap orto move to the previous or next screen’s queson.

For step-by-step programming informaon, see the installaon

instrucons for the peripheral device or the control panel’s

Installaon and Programming Guide from dealer.2gig.com.

Q1 WIRELESS ZONE PROGRAMMING

(Q1) SELECT RF SENSOR # (01 to 48)

Select: RF Sensor # (01 to 48)to select the desired zone opon. Then

tap 

Select: RF Sensor # Typeto select type. Then tap 

Select: RF Sensor Equipment Codeto select code (see Equipment

Codes on page 4). Then tap 

Enter: RF Sensor # Serial Number (7 Digits) Enter the serial number or

place the control panel into learning mode by tapping Shi >

Learn and then trip the sensor to transmit its serial number to

the control panel.

Select: RF Sensor # Equipment Ageto select (1) New or (2) Exisng

Then tap 

Select: RF Sensor # Loop Numberto select (1) 1, (2) 2, or (3) 3:

1-Use Loop 1 for all 2GIG products (except as noted in loops

below)

2-Thin door/window contact using internal switch

3-Flood/freeze sensors. Then tap

Select: RF Sensor # Dialer Delay (0 to 1)unl desired opon

Construct: RF Sensor # Voice Descriptor Tap Insert. Then tapto scroll

the available words or enter the 3-digit code associated with

the desired word. Tap Insert again before adding another word.

There is a ﬁve (5) word maximum. See Voice Descriptors on

page 4. Then tap 

Select: Select RF Sensor # Reports (0 to 1)to select (1) Enabled or (2)

Disabled. Then tap 

Select: Select RF Sensor # Supervised (0 to 1)to select (1) Enabled or

(2) Disabled. Then tap 

Select: Sensor Chime to select chime. Then tap 

SUMMARY OF RF SENSOR # SCREEN

The Summary shows the sengs for each sensor. Tap Edit Next to add the

next RF sensor, or tap Edit Current to reconﬁgure the current RF sensor. Tap

Q2 WIRED SENSOR PROGRAMMING

If no wired sensor programming is needed, tap Skip to go to Q3 Key Fob

Programming.

(Q2) ENTER WIRED SENSOR # (1 thru 2)

Select: Sensor (Zone) Typeunl desired opon

Select: Equipment Age (New/Exisng)unl desired opon

Select: Normal Stateunl desired opon

(0) Not Used, (1) Normally Closed, (2) Normally Open, or (3)

Mixed with no EOL. Then tap 

Select: Dialer Delay (Enabled/Disabled)unl desired opon

Construct: RF Sensor # Voice Descriptor Tap Insert. Then tapto scroll the

available words or enter the 3-digit code associated with the

desired word. Tap Insert again before adding another word.

There is a ﬁve (5) word maximum. See Voice Descriptors on

page 4. Then tap 

Select: Sensor Reports (Enabled/Disabled)unl desired opon

Select: Sensor Chimeunl desired opon

SUMMARY OF WIRED SENSOR # SCREEN

The Summary shows the sengs for each sensor. Tap Edit Next to add the

next wired sensor, or tap Edit Current to reconﬁgure the current wired sensor.

Tap Skip to move to Q3 Keyfob Programming.

Q3 KEY FOB PROGRAMMING

If no key fob programming is needed, tap Skip to go to Q4 Keypad Programming.

(Q3) SELECT FOB # (1 to 8)

Select: Fob <#> Used (0 to 1)to select (1) Disabled or (2) Enabled. Then tap



Select: Fob <#> Equipment Code to select code (see Equipment Codes on

page 4). Then tap 

Enter: Fob <#> Serial Number (7-Digits) Enter the serial number manually (7

digits) or place the panel into learning mode by tapping Shi > Learn

and then tap the Armed Away buon on the key fob unl the LED

illuminates and the sensor transmits the serial number.

Select: Fob # Equipment Age (0 to 1)to select (0) New or (1) Exisng. Then

tap 

Select: Fob # Emergency Key (0 to 4)to select (0) Disabled, (1) Auxiliary

Alarm, (2) Audible Alarm, (3) Silent Panic, or (4) Fire. Then tap 

Select: Fob Can Disarm (Enabled/Disabled)unl desired opon

Construct: RF Sensor # Voice Descriptor Tap Insert. Then tapto scroll the

available words or enter the 3-digit code associated with the desired

word. Tap Insert again before adding another word. There is a ﬁve (5)

word maximum. See Voice Descriptors on page 4. Then tap 

Select: Fob # Arm No Delay (0 to 1)to select (0) Disabled or (1) Enabled.

Then tap 

Select: Fob # Key # Output (0 to 2)to select (0) Disabled, (1) Toggle

Output, or (2) Momentary Output. Then tap 

SUMMARY OF FOB # SCREEN

The Summary shows the sengs for each sensor. Tap Edit Next to add the next

keyfob, or tap Edit Current to reconﬁgure the current keyfob. Tap Skip to move to Q4

Keypad Programming.

FIELD PROGRAMMING FOR COMMUNICATION

(Q13) SELECT TWO-WAY VOICE (0 TO 2)

Tap: Go To. Then enter 13 to select a two-way voice opon.

Select: Two-Way Voice (0 to 2)to select (1) Stay On Line or (2) Stay On Line,

Including Fire and CO Alarms. Then tap 

TO SETUP CELL PRIMARY: (Q8) SELECT DIALER (0 TO 1)

Tap: Go To. Then enter 08 to select the dialer.

Select: Dialer (0 to 1)to select (0) Disabled. Then tap 

Tap: Go To. Then enter 63 to select a phone fail detect opon.

Select: Phone Fail Detect (0 to 1)to select (0) Disabled. Then tap

TO SETUP POTS PRIMARY: (Q8) SELECT DIALER (0 TO 1)

Tap: Go To. Then enter 08 to select the dialer.

Select: Dialer (0 to 1)to select (1) Enabled. Then tap

Tap: Go To. Then enter 63 to select phone fail detect.

Select: Phone Fail Detect (0 to 1)to select (1) Enabled. Then tap

Tap: Go To. Then enter 11 to enter the CS Phone Number.

Select: CS #1 Phone Number (0-25 Digits) Enter the phone number. Then tap 

Tap: Go To. Then enter 12 to enter the CS Account Number.

Select: CS #1 Account Number (4 Digits) Enter the account number. Then tap

77-000010-001 Rev D

For technical support in the USA and Canada: 855-2GIG-TECH (855-244-4832) or visit the

2GIG dealer site at dealer.2gig.com, or email us at [email protected].

For technical support outside of the USA and Canada, contact your regional distributor.

Quick Programming Guide

Control Panel Firmware Version 1.13

Q4 KEYPAD PROGRAMMING

If no keypad programming is needed, tap Skip to go to Field Programming for

Communicaon.

(Q4) SELECT RF KEYPAD # (1 to 4)

Select: Keypad RF Keypad # (1 to 4)to select desired keypad number. Then

tap 

Select: RF Keypad # Used (0 to 1)to select (0) Disabled or (1) Enabled.

Then tap 

Select: RF Keypad # Equipment Codeto select code (see Equipment Codes

on page 4). Then tap 

If using a Wireless Keypad (2GIG-PAD1)

Enter: RF Keypad 1 Serial Number (7 Digits) Enter the serial number or

place the control panel into learning mode by tapping Shi > Learn

and then trip the sensor to transmit its serial number to the control

panel.

If using a Wireless Touch Screen Keypad (2GIG-TS1*)—*Not available in all

regions

Select: RF Keypad # Keypad ID (Read-Only) Tap the Learn buon. Then go to

the TS1 and tap the Pair WIth Panel buon. When the learning

operaon succeeds, tap OK on both the panel and TS1.

Select: RF Keypad 1 Equipment Age (0 to 1)to select (0) New or (1)

Exisng. Then tap 

Select: RF Keypad # Emergency Keys (0 to 1)to select (0) Disabled or (1)

Enabled. Then tap 

Construct: RF Sensor # Voice Descriptor Tap Insert. Then tapto scroll the

available words or enter the 3-digit code associated with the desired

word. Tap Insert again before adding another word. There is a ﬁve (5)

word maximum. See Voice Descriptors on page 4. Then tap 

SUMMARY OF RF KEYPAD # SCREEN

The Summary shows the sengs for each sensor. Edit Next to add the next keypad,

Edit Current to reconﬁgure current keypad. Tap Skip to move to Field Programming

for Communicaon.

Download the Control Panel Installaon Guide from dealer.2gig.com.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Quick Programming Guide

GETTING STARTEDTo enter the control panel’s System Conﬁguraon module to program sensor zones and modify sengs:1. At Home screen, tap logo in lower

Seite 2 - LED States

RESETTING THE SENSORBefore programming the image sensor into a new network, you must reset it as follows:1. Insert a paperclip into the hole on the

Seite 3 - Z-Wave Quick Programming

Add & Remove Z-Wave device screenPressing the device’s programming buttonAdding the 2GIG Z-Wave Programmable Thermostat (2GIG-CT100)PRESS Z-WAVE D

Seite 4 - Voice Descriptors

(0000) Other(0470) HW R-D/W “5818MNL”(0475) Exisng Glass Break Detector(0491) HW Panic Pendant “5802MN2”(0519) HW Glass Break “5853”(0530)

Kommentare zu diesen Handbüchern

Keine Kommentare

2gig Control Panel Firmware Version 1.13 - Quick Progra Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Zuhause 2gig Control Panel Firmware Version 1.13 - Quick Progra herunter. 2GIG Control Panel Firmware Version 1.13 - Quick Programming Guide User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Zuhause 2gig Control Panel Firmware Version 1.13 - Quick Progra