2gig PAD1-345 Keypad Bedienungsanleitung PDF herunterladen

Wireless Keypad 2GIG-PAD1-345

The 2GIG-PAD1-345 is a Wireless Keypad with stay and away arming

options as well as fire and panic emergency functions.

Installation & Mounting Guidelines

1. Simultaneously press both tabs on top of the keypad to separate

mounting plate from main keypad.

2. Place mounting plate in desired location and ensure the plate is level

(see

Figure 1

3. Secure the mounting plate with 4 screws in the provided holes (see

Figure 1

4. To connect the batteries, remove the two battery pull tabs located

near the metal clips (see

Figure 2

)

5. To reattach keypad insert the bottom portion onto the mounting plate first and then tilting upward, snap-

ping the keypad into place.

Programming

For programming details, refer to your

2GIG Installation & Programming Instructions

Testing

Before mounting the keypad, verify that the mounting location provides good RF communication to the panel. To

verify, do the following:

1. Put the control panel into sensor test mode.

2. Press and hold any numeric key for at least 2 seconds.

3. Listen for siren or keypad beeps to determine appropriate response (refer to the control panel installation

instructions).

4. Exit sensor test mode.

Note: It is recommended that a system test be performed per the Operation & User’s Guide at least once a year.

Battery Installation & Replacement

Use only the recommended replacement batteries (see

Specifications

To install or replace the battery, do the following:

1. Remove keypad from mounting plate (see

Installation & Mounting Guidelines

2. Place a small flathead screwdriver in the slot between the metal clip (see

Figure

2) and the battery and twist the screwdriver

slightly while holding back one of the black plastic edges holding the battery.

3. Insert the replacement battery with the + sign facing out. (see

Figure 2

)

4. Verify programming and RF communication with the panel. (see

Programming

WARNING! The polarity of the battery must be observed, as shown (see

Figure 2

). Improper handling of lithium

batteries may result in heat generation, explosion or fire, which may lead to personal injuries. Replace only with the

same or equivalent type of battery as recommended by the manufacturer. (see

Specifications

)

Batteries must not be recharged, disassembled or disposed of in fire. Disposal of used batteries must be made in accor-

dance with the waste recovery and recycling regulations in your area.

Keep away from small children. If batteries are swallowed, promptly see a doctor.

California Only: This Perchlorate warning applies only to Manganese Dioxide Lithium cells sold or distributed ONLY in California,

USA. Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.

Specifications

Wireless Signal Range 350 ft., open air, with 2GIG Wireless Alarm Control Panel

Code Outputs Key press 0-9; *; #; STAY; AWAY; FIRE; POLICE; Supervisory; Low Battery

Transmitter Frequency 345.000 MHz (crystal controlled)

Transmitter Frequency Tolerance ± 15 kHz

Transmitter Bandwidth 24 kHz

Modulation Type Amplitude Shift Keying—On/Off Keying (ASK-OOK)

Unique ID Codes Over one (1) million different code combinations

Supervisory Interval 70 minutes

Peak Field Strength Typical 50,000 uV/m at 3m

Dimensions (WxHxD) 5.73 x 4.25 x 1.00 in. (14.6 x 0.8 x 2.5 cm)

Weight (including battery & bracket) 7.75 oz. (219.7 g)

Housing Material ABS plastic and poly-carbonate

Color White with gray trim

Operating Temperature 32° to 120°F (0° to 49°C)

Relative Humidity 5-95% Non-Condensing

Battery (installed) Two (2) Panasonic CR2032, or equivalent Lithium batteries

Regulatory Listing(s) ETL, FCC Part 15, Industry Canada

Warranty* Two (2) years

Included Accessories Four (4) Phillip’s head screws, four (4) plastic wall anchors

FCC COMPLIANCE STATEMENT*

This device complies with FCC Rules and Regulations as Part 15 devices, as well as Industry Canada Rules and Regulations.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Note: Changes or modifications to the device may void FCC compliance.

FCC ID: WDQ-PAD1345

Industry Canada ID: 7794A-PAD1345

*For more warranty and compliance information, visit our website (www.2gig.com).

Figure 1

Operating Instructions

Technical Support:

1-866-670-1591

www.2gig.com

IPM-5020-02 Rev. B

Figure 2

Figure 1 1
Figure 2 1

Inhaltsverzeichnis

Seite 1 - Figure 2

Wireless Keypad 2GIG-PAD1-345 The 2GIG-PAD1-345 is a Wireless Keypad with stay and away arming options as well as fire and panic emergency funct

Kommentare zu diesen Handbüchern

Keine Kommentare

2gig PAD1-345 Keypad Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Zuhause 2gig PAD1-345 Keypad herunter. 2GIG PAD1-345 Keypad User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Zuhause 2gig PAD1-345 Keypad